Premium nanocrystalline transformer core factory: The toroidal transformer is a type of electronic transformer that features a donut-shaped core made from a continuous loop of magnetic material, typically iron powder or ferrite. This design allows for maximum efficiency in power transfer due to the minimal air gap between the windings and the core, resulting in low electromagnetic interference and reduced energy losses. Toroidal transformers from Transmart toroidal transformer supplier are commonly used in various applications such as audio equipment, amplifiers, medical devices, industrial machinery, and lighting fixtures. They are preferred over other types of transformers for their compact size, high efficiency, low noise levels, and ability to handle high currents with minimal heat generation. Their symmetrical shape allows for easy mounting and installation in tight spaces where conventional transformers may not fit. Read extra details at https://www.transmartcore.com/products-4714.
Characteristics and application of nanocrystalline magnetic core: High permeability, nanocrystalline Fe73 5Cu1Nb3Si13. 5B9 alloy has high saturation magnetic induction. The material becomes brittle after heat treatment and is easy to be processed into alloy powder. Compared with the nanocrystalline magnetic core wound with strip, the magnetic permeability of the nanocrystalline magnetic core is still very low and the soft magnetic properties are unstable. At present, the urgent problems to be solved are as follows: 1. Effectively control the growth of nanocrystals during heat treatment; 2. Molding of magnetic particle core; 3 Effect of heat treatment specification on soft magnetic properties of magnetic particle core.
The annealing temperature of iron-based amorphous alloy is lower than that of silicon steel, and the energy consumption is small, and the iron-based amorphous alloy magnetic core is generally manufactured by special manufacturers. Silicon steel magnetic cores are generally manufactured by transformer manufacturers. According to the above comparison, as long as it reaches a certain production scale, iron-based amorphous alloy will replace some silicon steel markets in electronic transformers within the power frequency range. In the medium frequency range of 400Hz to 10kHz, even if new silicon steel varieties appear, iron-based amorphous alloy will still replace most silicon steel markets with a thickness of less than 0.15mm.
Transmart amorphous core manufacturer & supplier is mainly engaged in the production and sales of amorphous core materials. The amorphous core transformer is one of Transmart Industrial’s multiple product series.Transmart Industrial’s amorphous C-core is manufactured in strict accordance with relevant national standards. Every detail matters in the production. Strict cost control promotes the production of high-quality and priced-low product. Such a amorphous transformer is up to customers’ needs for a highly cost-effective product.
We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Nanocrystalline magnetic core is a small part with magnetic conductivity. There are nanocrystalline particles with small particles in the center of nanocrystalline magnetic core. The working principle of nanocrystalline magnetic core is to absorb the common mode current in the cable through the principle of induction heating and convert it into heat to dissipate. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size. Read extra information on https://www.transmartcore.com/.
We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Hysteresis loss is the iron loss caused by the hysteresis phenomenon in the magnetization process of the iron core. The size of this loss is directly proportional to the area surrounded by the hysteresis loop of the material. The hysteresis loop of silicon steel is narrow, and the hysteresis loss of transformer core made of silicon steel is small, which can greatly reduce its heating degree.