Some recommendations for automotive hail damage repair tasks: For dents that are fairly small and not deep, a dent repair kit may be an inexpensive and simple solution. These kits are available at any auto parts store and tend to be very user friendly — instructions are always included. The best part is that they usually cost under $40. Most include several stems for various sized dents, a glue gun and a knockdown tool. You may be surprised at how well the kit works and how professional the result looks. We don’t recommend this kit for large, deep dents — you might cause even more damage trying to fix those with a kit.
1st let’s start with some car paint care tricks: Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.
Wax Your Car: Yes, I think it is accepted knowledge that your car needs to be waxed on a regular basis. If you have just bought a new car from a dealership, you must realize that no new car comes with wax from the manufacturer or dealer. New car prep does not mean the dealership is going to wax your car either. So that new car paint of yours is like taking a new-born child out in the sun with no sunblock on their skin. You can review my selection of best car waxes in helping you choose a quality car wax. Just remember your car should be waxed every 4-6 months under “normal” conditions. If you live in extreme weather conditions and you plan on keeping your car for over 5 years, you might consider applying wax to that new car paint even more frequently.
Not only can you unclog a drain with a plunger, but you can also get out small- to medium-sized dents out of your car too. Just splash some water on both the plunger and the dent and start pushing and pulling until it pops out. Make sure to use a cup plunger (for sinks), not a flange one (for toilets). Reversing into an object is one of the easiest ways to get a dent. So for plastic bumpers, even if you attempt to take off the bumper, it might still be difficult to push out the dent because of how stiff the plastic is. Solve this issue by boiling some water in a pot and throwing it on the dent.
In order to protect new car paint, you have to invest some time and effort to clean the vehicle on a regular basis. There are several car waxes and polishes available on the market. Although some car product manufacturers claim their products produce long lasting results, you will have to re-apply any product every few months, so the exteriors look appealing. If you’ve purchased a new vehicle that has a shiny coat of factory paint, avoid using too many detailing products as they rob the car of its original luster and also damage the paint. Read extra details on Automotive Hail Repair for Colorado Springs Area.
Dents near edges – If a dent of any size is situated near the very edge of a body panel or near a seam, PDR repair may be impossible. The reason for this is that in order to repair a dent using these techniques, you need to access the back side of the dent. The dent has a crease – If there is a sharp crease (like a folded page) in the dent, PDR likely will not work. Older vehicles – If your vehicle is older than 1990 or is a classic car, the odds are good that attempting paintless repair techniques on a dent will damage the paint. This is because the paint quality on older body panels can’t withstand the strain of the repair techniques.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.